Explore

 

 

Everybody is bound to have their own unique opinion in relation to A Step-by-Step Guide to Installing a Bathtub.

Setting up a tub isn't precisely brain surgery, however it does need strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is conveniently accessible, the project can move speedily; if you have to open a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either situation, the project is within a home handyman's skills, although you will need a helper to move out the old tub as well as set in the new one. Ensure you have certified on your own for the work and also fit attempting it. Rather than employing a professional to take over a halfway-completed job, it is much better to think about utilizing one before you begin. Chances are you might require an expert plumber to make tube connections.
This short article will aid you mount a new bathtub in your bathroom if you have actually currently purchased a new bathtub and also do not require to transform the plan of your previous water system pipes.
Your tools and product list must make up the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Measuring tape


• Pipe Caps


 

Removing Old Taps

If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the water supply. After doing so, activate the faucets to drain any kind of water staying in the system. The process of eliminating the existing taps can be fairly troublesome due to the limited gain access to that is often the situation.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.

 

 

Fitting New Touches

If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin guaranteeing that the washers remain in location in between the tap and the sink. Secure the faucet in position with the producer given backnut. Once the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap adapters. The previous type ought to be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

 

 

Setting up the Tub

Making use of the two wooden boards under its feet, put the bath tub in the required setting. The wood boards are handy in evenly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The next goal is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the tub up until the spirit level checks out degree.
To mount faucets, fit all-time low of the furthest flexible tap port to the proper supply pipeline by making a compression sign up with; after that do the very same for the other tap.
Switch on the supply of water as well as inspect all joints and also brand-new pipework for leakages and also tighten them if essential. Fill the bathtub and also check the overflow outlet and the regular electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling and sealing around the bath tub needs to wait up until the tub has actually been made use of at the very least when as this will certainly resolve it right into its last setting.

 

 

Getting ready for the Setup

First of all, the supporting frame supplied with the bath should be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to make certain that if the faucet includes a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the taps device to avoid strain on the bath tub.
Fit the versatile tap adapters to the bottom of both taps making use of 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its final setting.

 

 

Tiling Around the Bathtub

In the area where the bathroom meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to split a rigid seal, creating the water to penetrate the wall surface between the bathroom as well as the tiling, bring about problems with dampness as well as possible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of drenched newspaper or soft rope. Remember to always load the bath tub with water prior to sealing, to enable the movement experienced when the tub remains in use. The sealer can fracture relatively very early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also quickly readily available on the marketplace. It is advisable to fit the ceramic tiles utilizing waterproof or water-proof adhesive and grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Do you really like more info about Installing A Bathtub? Try to leave a remark further down. We will be delighted to see your views about this blog posting. Hoping to see you back again before long. I beg you set aside a second to promote this blog entry if you enjoyed reading it. We take joy in reading our article about A Step-by-Step Guide to Installing a Bathtub.

Schedule